The thickness is out. Shell 10T, top head 4T, bottom head 12T. Design feels done, right? But in this state you can't order a single plate. To order, there's still a chain to walk.
What goes on the purchase order isn't "10T thickness." It's buyable sizes and quantities like "so many 1,219 × 2,438 plates, so many 1,000 × 2,000 plates." To get there:
How you lay the shell and heads on standard plates changes the sheet count and yield; only once the layout is set do you know where and how many weld lines appear; and only with the weld lines do you get the non-destructive test (RT) quantity and inspection cost. Only then are the order and quote complete. With just a thickness you can't order anything.
This is where it hurts most by hand. Say, during design review, you raise the bottom head from 10T to 12T. Then:
In Excel you fix one cell, but the material list (BOM) has to be rebuilt by hand. Nesting again, RT quantity again. The price of changing one thickness cell is redoing this whole chain. So you can't touch thickness lightly during review, and touching it costs another half a day.
Even once the thickness is set, the chain passes through a person's hands a few more times. The report says shell 5T, head 8T; a person copies those numbers into the drawing dimensions, then copies the drawing's plate sizes into the material list (BOM). Each step is simple repetition — but the simpler the repetition, the more mistakes slip in.
Such mismatches mostly slip by quietly. A single number, invisible, blows up only on the floor or at inspection. By then it's already rework.
The fix is simple — don't copy. If the thickness the strength calculation decided becomes the drawing dimension directly, and the material list directly, the three documents come from one and the same design. With no copying step, there's no place for them to drift apart.
Where a person steps in should be judgment, not copying — whether this geometry suits the floor, whether to add a special part. Moving numbers around is the program's job.
If thickness through the drawing and material list were connected as one calculation, the moment you change one thickness the nesting, the weld map, the RT quantity and the material list all recompute together. No rebuilding the BOM by hand.
Run one real case and these come out together with the thickness — 11 plates across 5 sizes, 40 EA of weld lines and inspection, a cutting list. Change the thickness and all these numbers move with it. Not rework, just recomputation.
When calc → drawing → BOM come out in one pass, three things change.
Q. Can you order as soon as the strength calculation gives a thickness?
No. A purchase order needs buyable plate sizes and sheet counts, not a thickness. The plate layout (nesting), weld-line layout, inspection (RT) quantity and material sizes and counts all have to be settled before the order and quote are complete.
Q. What has to be redone if a thickness changes during design review?
That part's weight, the plate layout with its sheet count and yield, and sometimes the welding and inspection quantities change in a chain. By hand you rebuild the nesting, RT quantity and BOM; AUTONEST VC recomputes them together when you change the thickness.
Q. Why do the report, drawing and BOM end up disagreeing?
Because a person copies the numbers across. The report says 8T but the drawing says 6T, the BOM is one sheet short, or the spec changed and only one of three documents was fixed. These slip by quietly and show up as rework on the floor or at inspection.
Q. How does AUTONEST VC produce the drawing and BOM?
The thickness the strength calculation decided becomes the drawing dimension directly, and the material list directly. The report, drawing and BOM come from one and the same design, so there is no copying step.
Q. What comes out together when you run one case?
In one real case, 11 plates across 5 sizes, 40 EA of weld lines and inspection, and a cutting list came out in one pass together with the thickness. Change the thickness and these numbers move with it.
"Is design done?" and "can you order?" are different questions. Between them lies the chain you used to walk by hand — nesting, weld map, inspection, and copying into the drawing and BOM. Tie that chain together with the same design and hours become minutes, and the two questions have the same answer.
Related — Why AUTONEST — the reason we brought drawing and calculation into one nest