Newcomers almost always ask: "So one button and everything comes out?"
Mostly, yes. It finds the thickness, works the size back from capacity, judges nozzle
reinforcement, draws the drawing, pulls the material list, and even lays it out on the plate. And
yet there are places we could automate but deliberately did not. This
post is about those places.
Trying thickness candidates one by one while going back and forth on the external-pressure chart; rewriting the drawing, material list and weld lengths every time the thickness changes — this is repetition, not judgment. A person doesn't produce a better answer, and gets it wrong when tired. All of this should go to the machine.
Conversely, there are places where automating produces an answer but leaves no one to take responsibility. Push in there and the tool looks impressive while the output becomes unusable.
Design pressure, design temperature, material, corrosion allowance, whether there's vacuum. These are the input to the calculation, not its result. They are set in the process, agreed with the client, and go straight into the contract and inspection documents.
The moment the tool fills in "for this capacity people usually use 0.5 MPa, so I put that in," the source of that number disappears. An output where, when a reviewer asks "who set this pressure?", the answer is "the program put it in on its own" cannot be used on the floor.
So AUTONEST VC does not recommend design conditions. It takes them as input and only answers whether the calculation holds under those conditions.
For the same reason, the plate thickness list and standard plate sizes are managed by the user. Every company has different suppliers and different plates left in the warehouse. If we set a standard and pushed it down, it wouldn't be that company's reality.
Clamps, gaskets, special fittings. We left these not because they can't be automated, but because practice differs by company.
If there's one standard, automation gives the right answer. If the standard differs by company, automation gives a wrong answer with confidence. And a confident wrong answer is far more dangerous than a blank — everyone sees a blank, but a plausible number no one checks again.
Here we take input. In return, we take responsibility for propagating that value accurately into the downstream calculation, drawing, and material list.
The cost-saving features also show the options and stop.
The request we hear most is "make the drawings come out complete in one go, too." Before answering, one thing has to be split apart — "drawing" is used in two senses.
Let us be clear that the reason isn't technical. Matching one company's format is not hard. What is hard is that it doesn't become a product. Fit it to one company and the next one starts from scratch. With one standard you build one feature; with a standard per company you build one per company and keep maintaining them all. And a format isn't one sheet — vessel type, fittings and drawing type each branch, multiplied by company practice, and every rule change means rework. So it isn't something to add on top of the program; it is custom development for that company, scoped on its own.
If you are willing to commission that, there is no reason it can't be done — then we talk about it as a development project, not as the program. Meanwhile the boundary is this: the drawing comes as a file (DXF) you open straight in your CAD, a drawing you edit right away, not a picture file. You finish your company format on top of it — no redrawing of geometry or dimensions.
If "one-stop" means not "one button" but "do I have to redraw it?", that point has already been passed.
Design rules don't end with one thickness formula. In this geometry do this, in that combination do that — counting the detailed rules, there are far more. Among them are rules we could code but chose not to. Not because we couldn't, but because we decided against it.
For example, when you cut a manway or nozzle opening into a head, there is a principle that the opening should not exceed half the head diameter. Coding it is easy — compare the two diameters and warn if it's over. But in real designs this boundary is almost never reached. Add logic to catch a case that comes up once in several years and the code gets more complex, the maintenance burden stays, and the accidents it actually prevents are few.
So rules are handled two ways. Rules that are hit often — corrosion allowance, external pressure, nozzle reinforcement — are all inside the calculation and show on screen when they fall short. Rules that are almost never hit are left for a person to catch. That isn't neglect; it's a deliberate call, with one criterion: the chance of meeting it in real use, weighed against the complexity it adds.
Designs above half do exist. In practice, some go further on proper grounds, backed by separate reinforcement or analysis. Everything else runs automatically, so stopping the whole calculation to catch this one point would cut the automation off right there — a five-second automatic job becomes five or ten minutes by hand.
The bigger reason: whether that opening went through separate reinforcement or was justified by separate analysis is a basis you can't see from the drawing and the numbers. The software has no way to judge it, so stopping anyway is less a safeguard than throwing the problem back because it can't judge. So the calculation continues past this boundary, and the basis for going past it stays with the designer.
No. This program does the calculation for you; it does not replace the designer. When a result comes out without a warning for an unusual geometry or combination, that is not "a guarantee that every such case is safe." AUTONEST VC doesn't know the rules on your behalf — it is an assistant that saves time for a designer who already knows them. In the hands of someone who knows, hours become minutes; in the hands of someone who doesn't, only numbers come out.
If a design program promises 100%, that is the one to be suspicious of. We chose instead to tell you how far we put into code, and where we left it to people.
There's a trap automation tools fall into easily: forcing a pass somehow. If it can't find a thickness, quietly relaxing the conditions, or leaving an innocuous phrase in the judgment cell to move on.
AUTONEST VC goes the other way. If the thickness is short it first tries raising it, and if that still fails it writes that it fails, visibly. Instead of a blank or a leftover value from a previous case, the fact that it doesn't hold under these conditions stays on the output. A report that quietly passed going out to the floor is always more expensive than one that's caught in plain sight.
A modern tool might well put AI in the calculation too, but here we deliberately didn't. A strength calculation must give the same answer for the same conditions, and you must be able to trace which clause and which chart that answer came from. Something that answers by probability can't do either.
When an inspector reopens the same report next month, the same numbers must be there. That isn't a preference — it's the minimum condition of an output.
| What the machine does | What the person does |
|---|---|
| Internal/external-pressure thickness search, size back-calculation from capacity, head/ jacket/flange/closure design, nozzle reinforcement judgment, drawing, material list, weld map, plate layout | Confirming design conditions, specifying non-standard fittings, finishing the company drawing format, deciding whether to adopt a saving, judging the basis for rarely-hit rules (such as head openings), final review and approval |
The quality of automation is decided not by how much you automated but by where you stopped. Take all the repetition, leave the judgment exactly where it belongs. The reason an hours-long job becomes minutes, and the reason a reviewer trusts the resulting report, come from the same place.
Q. Does AUTONEST VC do everything with one button?
Mostly, yes — thickness search, size back-calculation, nozzle reinforcement judgment, drawings, the material list and plate layout. But design conditions, non-standard fittings, each company's drawing format and the final judgment are deliberately left to people.
Q. Does the program recommend design conditions?
No. Design pressure, design temperature, material, corrosion allowance and vacuum are inputs to the calculation, so it doesn't recommend them. It only answers whether the calculation holds under the conditions you enter.
Q. Will it match my company's drawing format (title block, drawing numbers)?
The design drawing comes as a drawing file (DXF) you open in your CAD and edit right away, and you finish your company format on top of it. Matching one company's format is a separate custom development project, not part of the program.
Q. Does it warn when a head opening exceeds half the head diameter?
That principle is not coded. It is almost never reached in real designs, and some designs go past it on proper grounds with separate reinforcement or analysis, so the calculation continues. The basis for going past it is the designer's call.
Q. Does the calculation use AI?
No. A strength calculation must give the same answer for the same conditions, and you must be able to trace which clause and which chart it came from.
Q. With AUTONEST VC, do I still need to know the design rules?
Yes. It doesn't know the rules on your behalf — it saves time for a designer who already knows them. In the hands of someone who knows, hours become minutes.