Pressure Vessel Strength Calculation Report Sample — Single Vacuum · Jacketed 2,000 L (Notice No. 2025-61)
Two hypothetical cases (A: single tank under vacuum, 2,000 L · B: jacketed tank, 2,000 L, jacket design pressure 0.5 MPa · design temperature 160 °C) calculated with AUTONEST VC: the report PDFs, required and used thickness with the result for each part, and an approximate cross-check of the external-pressure chart values — published as they are.
Calculation basis: “Standard for Inspection and Inspection Exemption of Heat-Using Equipment” (unofficial English translation; MCEE Notice No. 2025-61, Korea, partially amended 18 Dec 2025) — the Korea Energy Agency inspection-target basis. All figures are taken from the report PDFs below. The reports are in Korean.
Design conditions
| Item | A · Single, vacuum | B · Jacketed |
|---|---|---|
| Type | Single (with manhole) | Jacketed (with manhole) |
| Working capacity | 2,000 L (2 m³) | 2,000 L (2 m³) |
| Shell (inner vessel) material | A240-316L | A240-316L |
| Shell ID × length | 1,345 × 1,480 mm | 1,345 × 1,480 mm |
| Heads (top · bottom) | 10% torispherical (dished) | 10% torispherical (dished) |
| Inner design pressure | 0.3 MPa · vacuum −0.1 MPa | 0.3 MPa · vacuum −0.1 MPa |
| Inner design temperature | 120 °C | 120 °C |
| Inner external design pressure | 0.1 MPa (vacuum) | 0.6 MPa (jacket 0.5 + vacuum 0.1) |
| External-pressure design temperature | 120 °C | 160 °C |
| Jacket material | — | A240-304 |
| Jacket ID · length | — | 1,455 mm · 1,245 mm |
| Jacket design pressure · temperature | — | 0.5 MPa · 160 °C |
| Corrosion allowance | 0.0 mm | 0.0 mm |
| Joint efficiency (shell / head) | 0.95 / 1.0 | 0.95 / 1.0 |
| Hydrostatic test pressure | 0.51 MPa | inner 0.51 MPa · jacket 0.85 MPa |
Key results
Required thickness is the minimum (calculated) thickness in the report. The value in brackets after the used thickness is the actual thickness after plate tolerance (and forming thinning for heads); that value is compared with the required thickness. For external pressure, the allowable external pressure is calculated from the used thickness and compared with the external design pressure.
AA · Single, vacuum (inner external pressure 0.1 MPa)
| Part | Clause | Required | Used | Result |
|---|---|---|---|---|
| Shell · internal | [30.1.1] cylindrical shell | 2.00 mm | 6 mm (5.75) | OK |
| Shell · external | [30.3] · [Fig. 30.5] | allowable 0.17 MPa ≥ design 0.1 MPa | 6 mm | OK |
| Top head · internal | [31.3.1] dished head | 2.93 mm | 5 mm (4.15) | OK |
| Top head · external | [31.6] head, pressure on convex side | allowable 0.11 MPa ≥ design 0.1 MPa | 5 mm | OK |
| Bottom head · internal | [31.3.1] dished head | 2.93 mm | 5 mm (4.15) | OK |
| Bottom head · external | [31.6] head, pressure on convex side | allowable 0.11 MPa ≥ design 0.1 MPa | 5 mm | OK |
| Nozzle N1 reinforcement (3S · 316L · top, ID 150 · thickness 10) | [34.8] reinforcement of openings in heads | required area 438.9 mm² | effective area 446.2 mm² | OK |
| F-manhole_TOP_Loose_flange (top head) | [35.1] pipe flange for nozzles | 36.4 mm | 40 mm | OK |
| F-manhole_BTM_Loose_flange (shell) | [35.1] pipe flange for nozzles | 31.4 mm | 32 mm | OK |
| Sight glass | [34.5] sight glass thickness | 7.60 mm | 12 mm | OK |
BB · Jacketed (inner external pressure 0.6 MPa = jacket 0.5 + vacuum 0.1)
| Part | Clause | Required | Used | Result |
|---|---|---|---|---|
| Inner shell · internal | [30.1.1] cylindrical shell | 2.00 mm | 15 mm (14.75) | OK |
| Inner shell · external | [30.3] · [Fig. 30.5] | allowable 0.77 MPa ≥ design 0.6 MPa | 15 mm | OK |
| Top head · internal | [31.3.1] dished head | 2.93 mm | 5 mm (4.15) | OK |
| Top head · external | [31.6] head, pressure on convex side | allowable 0.11 MPa ≥ design 0.1 MPa | 5 mm | OK |
| Bottom head · internal | [31.3.1] dished head | 2.93 mm | 18 mm (15.77) | OK |
| Bottom head · external | [31.6] head, pressure on convex side | allowable 0.62 MPa ≥ design 0.6 MPa | 18 mm | OK |
| Jacket shell · internal (A240-304) | [30.1.1] cylindrical shell | 3.39 mm | 4 mm (3.75) | OK |
| Jacket head · internal (A240-304) | [31.3.1] dished head | 4.95 mm | 6 mm (5.09) | OK |
| Jacket closure (flat plate) | [31.16.4.6] jacket closure design | 15.58 mm | 18 mm | OK |
| Closure sleeve for nozzle through the jacket (OD 360, cylinder under jacket pressure as external pressure) | [30.3] · [Fig. 30.5] | allowable 2.50 MPa ≥ design 0.5 MPa | 8 mm | OK |
| Nozzle N1 reinforcement (3S · 316L · top, ID 90 · thickness 6) | [34.8] reinforcement of openings in heads | required area 263.3 mm² | effective area 271.9 mm² | OK |
| Sight glass (2) | [34.5] sight glass thickness | 6.30 mm · 6.33 mm | 12 mm · 12 mm | OK |
In B the bottom head sits inside the jacket and is checked at 0.6 MPa external pressure, while the top head is outside the jacket and is checked at 0.1 MPa vacuum — which is why their thicknesses differ. The jacket closure is checked for thickness and for jacket width (40 mm ≤ allowable 129.66 mm).
Figures in the tables are from the calculation pages of the report. The summary sheet shows three decimal places; the calculation pages round to two (e.g. allowable external pressure A shell 0.170 · heads 0.114, B shell 0.768 · top head 0.114 · bottom head 0.615).
External pressure: approximate cross-check of chart readings (not a precise verification)
Values read by eye from the chart and values from a published approximate formula differ by about 10%. This comparison is an approximate check that the report values are in a sensible range — it is not a precise verification. Both values exceed the 0.1 MPa external design pressure, so the result is the same.
Sample A shell (used thickness 6 mm, 5.75 mm after tolerance, external design pressure 0.1 MPa) — report values as printed:
| Report (Notice chart reading) | Approximate formula | |
|---|---|---|
| Do / ta · L / Do | 235.9 · 1.26 | same |
| A | 0.00031 | 0.000291 |
| B (316L, 120 °C) | 30.2 MPa | 27.0 MPa |
| Allowable external pressure Pa = 4B / (3·Do/ta) | 0.17 MPa | 0.153 MPa |
| Result (≥ 0.1 MPa) | OK | OK |
Approximate formula used (published): the Windenburg–Trilling approximation for elastic buckling of short cylinders, A ≈ 1.30·(t/Do)1.5 / (L/Do − 0.45·(t/Do)0.5), and B = A·E/2 in the elastic part of the chart (E = 185.8 GPa, read from the elastic line of the chart in the report).
Assumptions and limits
Scope of this sample and of VC calculations
- Calculation basis: the strength-calculation clauses of MCEE Notice No. 2025-61, “Standard for Inspection and Inspection Exemption of Heat-Using Equipment” (unofficial English translation); clause numbers are shown on each report page.
- Materials: STS316L (A240-316L), STS304 (A240-304).
- Design pressure below 1.0 MPa. External-pressure calculation within the temperature range of the Notice charts (316L up to 425 °C, 304 up to 650 °C).
- Types: single, jacketed and flanged (incl. bolted cover) — 6 types; heads 10% torispherical and 2:1 semi-ellipsoidal (flat plate for flanged covers).
- Basic inputs = type, capacity, pressure, temperature. Everything else (nozzles, manhole, sight glass, rupture disc, safety valve, thickness list) is calculated together with default values, and all of it can be changed.
Not calculated
- Strength of supports (legs, saddles, skirts, lugs), wind load, seismic load, external nozzle loads, fatigue.
Good to know
- A and B for external pressure are read from the Notice charts, so they carry reading error (see the cross-check above).
- Whether a vessel is subject to inspection, and the final judgement of conformity, are decided by the inspection body.
- This sample uses hypothetical conditions (not a real customer or product). Do not use it as-is for actual design or submission.
Download the report PDFs
Some pages omitted: the material comparison pages, which quote material standard names, were left out of the export. Every page is marked as a sample.
Try it with your own conditions
A report in the same format is produced from your own conditions (type, capacity, pressure, temperature).
AUTONEST VC — install and trial →
This page and the PDFs are examples built on hypothetical conditions and are not for actual design or inspection submission. Figures are copied from the reports AUTONEST VC produced for these conditions; the designer reviews and approves calculation results, and the inspection body decides whether a vessel is subject to inspection and gives the final judgement of conformity.